skyworks solutions, inc. ? phone [781] 376-3000 ? fax [781] 376-3100 ? sales@skyworksinc.com ? www.skyworksinc.com 200357 rev. c ? skyworks proprietary information ? products and product information are subject to change without notice. ? september 25, 2006 1 sky65016-70lf: ingap cascadable amplifier lf?3 ghz data sheet applications wireless infrastructure: wlan, hlan, dbs, broadband, cellular base stations test instrumentation catv features broadband: lf?3 ghz small signal gain: 20 db typ. @ 2 ghz high output 3rd order intercept: 27 dbm typ. 0 p 1 db : 14 dbm typ. @ 2 ghz input and output impedance: 50 nominal single, positive dc supply voltage sot-89 package available lead (pb)-free, rohs compliant and green msl-1 @ 260 c per jedec j-std-020 50 50 description the sky65016 is a general-purpose, broadband amplifier fabricated from skyworks ingap hbt process and packaged in a sot-89 package. the amplifier's input and output imped- ances are 50 , which allows these amplifiers to be cascaded without external impedance matching networks. the typical -3 db bandwidth of the sky65016 is lf?3 ghz. this amplifier is also available in the miniature sc-88 package (sky65016-92lf) and the plastic micro-x package (sky65016-214lf). the sky65016 is lead (pb)-free and rohs compliant. it is also ?green??environmentally friendly, containing no antimony or halogens such as bromine. a populated evaluation board is available upon request. full scattering parameters for this part are available for download at www.skyworksinc.com functional block diagram skyworks green products are lead (pb)-free, rohs (restriction of hazardous substances)-com pliant, conform to the eia/eicta/jeita joint industry guide (jig) level a guidelines, and are free from antimony trioxide and brominated flame retardants. new
skyworks solutions, inc. ? phone [781] 376-3000 ? fax [781] 376-3100 ? sales@skyworksinc.com ? www.skyworksinc.com september 25, 2006 ? skyworks proprietary information ? products and product information are subject to change without notic e. ? 200357 rev. c data sheet ? sky65016-70lf 2 parameter symbol condition frequency min. typ. max. unit small signal gain gp 2 ghz 19 20 21 db 3 db gain bandwidth bw 3 db 2.5 3 ghz noise figure nf 2 ghz 4.8 db output power at 1 db compression 0 p 1 db 2 ghz 13 14 dbm input and output vswr vswr 0.1?5 ghz 1.9:1 2.0:1 output third order intercept point oip3 p in = 0 dbm each tone, f = 10 mhz 2 ghz 27 dbm operating voltage v d measured at pin 3 3.2 3.5 3.7 v reverse isolation |s 12 | 0.1?6 ghz 20 db gain flatness 10 mhz?3 ghz 1.5 db thermal resistance jc 70 c/w electrical specifications at 25 c t = 25 c, i s = 40 ma, p in = 0 dbm, z 0 = 50 , measured in evaluation board, unless otherwise noted 123456 frequency (ghz) small signal gain vs. frequency gain (db) 0 25 25 c 85 c 20 15 10 0 5 -40 c frequency (ghz) input return loss vs. frequency return loss (db) 0 -15 -10 -5 -40 c 85 c 25 c -25 -20 -30 1 2 3 4 6 5 0 frequency (ghz) output return loss vs. frequency return loss (db) 0 -15 -20 -10 -5 -40 c 25 c 85 c -25 1 2 3 4 6 5 0 1 2 3 4 6 5 frequency (ghz) isolation vs. frequency isolation (db) 0 -10 -25 -20 -15 -35 -30 -40 -40 c 25 c 85 c typical performance data z 0 = 50 ,i s = 40 ma, measured in evaluation board, unless otherwise noted
data sheet ? sky65016-70lf skyworks solutions, inc. ? phone [781] 376-3000 ? fax [781] 376-3100 ? sales@skyworksinc.com ? www.skyworksinc.com 200357 rev. c ? skyworks proprietary information ? products and product information are subject to change without notice. ? september 25, 2006 3 characteristic value rf input power 15 dbm supply voltage 5 v supply current 120 ma power dissipation @ t = 25 c 500 mw operating temperature -40 c to +85 c storage temperature -65 c to +125 c absolute maximum ratings pin number pin name description 2, 4 gnd equipotential point ? internal circuit com- mon, which must be connected to the pcb ground or common via the lowest possible impedance. pin 4 must be connected via a low thermal resistance path to a good heatsink. 1 input rf input ? rf input with 50 nominal input impedance. an internally generated dc voltage is present at this pin, so an external dc block should be used to connect this pin to the external circuit. 3 output rf output ? dc supply voltage input and rf output with 50 nominal output impedance. the nominal voltage required at this pin is listed in the electrical specifications table. supply current is determined by an external resistor connected between the dc power supply and this pin. pin descriptions performance is guaranteed only under the conditions listed in the specifications table and is not guaranteed under the full range(s) described by the absolute maximum specifications. exceeding any of the absolute maximum/minimum specifications may result in permanent damage to the device and will void the warranty. caution: although this device is designed to be as robust as possible, electrostatic discharge (esd) can damage this device. this device must be protected at all times from esd. static charges may easily produce poten- tials of several kilovolts on the human body or equipment, which can discharge without detection. industry-standard esd precautions must be employed at all times. sot-89 1.50 0.10 0.381 0.025 s harp r0.10 7 7 4.0 9 0.10 all mea s urement s are in millimeter s 1.50 0.4 6 r0.10 s ide view end view bottom view 1 2 3 half etching depth 0.100 pin out (top view) 1 23 4 re c ommen d e d s ol d er reflow profiles refer to the ?recommended solder reflow profile? application note. t ape an d reel information refer to the ?discrete devices and ic switch/attenuators tape and reel package orientation? application note.
skyworks solutions, inc. ? phone [781] 376-3000 ? fax [781] 376-3100 ? sales@skyworksinc.com ? www.skyworksinc.com september 25, 2006 ? skyworks proprietary information ? products and product information are subject to change without notic e. ? 200357 rev. c data sheet ? sky65016-70lf 4 evaluation board input output r 1 l 1 c 1 c 4 c 2 v d v s i s l 3 l 2 the sky65016 evaluation board comprises the sky65016 amplifier, the input and output of which are connected via 50 microstrip transmission lines with dc blocking capacitors, c 1 and c 2 , to the input and output sma connectors, respectively. the positive supply voltage, v s , is connected to pin 3, rf output of the amplifier via the decoupling network which consists of c 4 , l 1 ,l 2 and r 1 . the power supply current, i s , must be limited, either via the current limit function of an external bench power supply, or by replacing l 3 with resistor r 1 , the value of which is given in the current limiting resistor values table. the evaluation board is shipped with l 3 in place, which shifts an in-band series resonance of the supply decoupling network out of band. for low frequency applications, r 1 may be used to conveniently limit supply current on the evaluation board. the evaluation board also contains a probe fixture which facilitates the direct measurement of the s parameters of the sky65016. the probe fixture comprises a very short coplanar waveguide (cpw) transmission line to pin 1 and an identical line to pin 3. all other pins of the amplifier are grounded. the cpw transmission lines are compatible with ground-signal-ground wafer probe tips, which can be connected to the rf ports of a vector network analyzer (vna) via coaxial cables. the very small electrical length of these cpw transmission lines obviates the need to de-embed their effects from the s parameters that are measured. the supply constant current must be applied via the bias tee, which is typically integrated into the vna, which is cas- cade with the output pin of the amplifier. component description value size suggested part number comments c 1 ,c 2 ,c 4 capacitor 47 nf 0603 l 1 inductor 33 nh 0603 l 2 ferrite bead FBMH4525HM162N-T r 1 resistor see current limiting 0603 resistor values table u 1 amplifier sky65016 evaluation board parts list v s ,v r 1 minimum power resistance, dissipation rating, mw 4 13 125 4.6 28 125 5 38 125 6 63 125 8 113 250 9 138 500 10 163 500 12 213 500 current limiting resistor values
data sheet ? sky65016-70lf skyworks solutions, inc. ? phone [781] 376-3000 ? fax [781] 376-3100 ? sales@skyworksinc.com ? www.skyworksinc.com 200357 rev. c ? skyworks proprietary information ? products and product information are subject to change without notice. ? september 25, 2006 5 copyright ? 2002, 2003, 2004, 2005, 2006, skyworks solutions, inc. all rights reserved. information in this document is provided in connection with skyworks solutions, inc. (?skyworks?) products or services. these mate rials, including the information contained herein, are provided by skyworks as a service to its customers and may be used for informational purposes only by the customer. skyworks assumes no r esponsibility for errors or omissions in these materials or the information contained herein. skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other diffic ulties arising from any future changes. no license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. sky works assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of skyworks products, information or material s, except as may be provided in skyworks terms and conditions of sale. the materials, products and information are provided ?as is? without warranty of any kind, whether express, implied, statutory, or ot herwise, including fitness for a particular purpose or use, merchantability, performance, quality or non-infringement of any intellectual property right; all such warranties are hereby expressly disclaimed. skyworks does not warrant the accuracy or completeness of the information, text, graphics or other items contained wit hin these materials. skyworks shall not be liable for any damages, including but not limited to any special, indirect, incidental, statutory, or consequential dam ages, including without limitation, lost revenues or lost profits that may result from the use of the materials or information, whether or not the recipient of mate rials has been advised of the possibility of such damage. skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which th e failure of the skyworks products could lead to personal injury, death, physical or environmental damage. skyworks customers using or selling skyworks products for use in such applications do so at their own risk and agree to fully indemnify skyworks for any damages resulting from such improper use or sale. customers are responsible for their products and applications using skyworks products, which may deviate from published specific ations as a result of design defects, errors, or operation of products outside of published parameters or design specifications. customers should include design and operating safeguards to m inimize these and other risks. skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of skyworks products outside of stated published specifications or parameters. skyworks, the skyworks symbol, and ?breakthrough simplicity? are trademarks or registered trademarks of skyworks solutions, inc., in the united states and other countries. third-party brands and names are for identification purposes only, and are the property of their respective owners. additional information, including rel evant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.
|
